Factory tubes included. Factory cartons Included. These are the newer version of the Snappers with toggle switches in the back, new serials number, first owner. Features and Specifications Manley SNAPPER® Input Impedance RCA: 475 kOhm
Input Impedance XLR: 15 kOhm (or 600 Ohm switchable on units before MSN524)
Input Sensitivity RCA: 750mV input = 110W output
Input Sensitivity XLR @ 15 kOhms: 1.5 V input = 110W output
Input Sensitivity XLR @ 600 Ohms: 2.4 V input = 110W output (w/600 Ohm source)
Gain RCA: factory set for 31 dB; Range = 29.5 to 34.5dB
Gain XLR: factory set for 25 dB
Negative Feedback: factory set for 9dB of global NFB
Maximum Output Power into 5 Ohms: 110 Watts (1.5% THD @ 1kHz)
Maximum Output Power into 8 Ohms: 100 Watts (1.5% THD @ 1kHz)
Signal to Noise Ratio Ref. 1W: Typically 90 dB A-WGT 20-20K
Noise Floor: Typically 105V = -77dBu A-WGT; Typically 388V = -66dBu unweighted
Will Scratch Your Floor: Use pennies under pointed feet to avoid marring cabinetry. Try quarters if you are in upper tax brackets. The bargain performer would be nickels. Paper currency does not function as well. Euro coins work 1.54 times better.
Dynamic Range: 98dB
THD+noise @ 1W: less than 0.1%
Frequency Response at 110W full power: 15 Hz to 40 kHz FLAT
Frequency Response at 5W into 5 Ohms: 10 Hz to 65 kHz FLAT, -3dB @ 100KHz
Recommended Speaker Load: Optimized for 5 Ohms
Actual Output Impedance: 1.5 Ohms
Power Consumption (idle): 170 Watts (1.4A @120VAC)
Power Consumption (at Full Power 110W): 336 Watts (2.8A @120VAC)
Operating Mains Voltage: Factory set for 100V, 120V or 220-240VAC operation for original destination country's mains voltage.
Operating Mains Voltage: changeable with power transformer re-wiring and fuse value change.
Mains Voltage Frequency: 50~60Hz
Input Vacuum Tube: 1 x 12AX7 Russian with 6CA7 or KT77 output tubes; use 12AT7EH large plate Electro-Harmonix Russian with EL34 types
Driver Vacuum Tube: 1 x 7044 or 5687 GE JAN NOS
Output Vacuum Tubes: 4 x 6CA7 (or EL34 equavalent)
B+ Voltage: 570V DC
Output Tube Quiescent Standing Current: 30mA
Set Bias for: 300mVDC measured across 10 Ohm cathode resistor
Lamp type: "FuseLamp" size 1/4" X 1 1/4", 12 volt, 0.15 amp; Units built after 5/2003 use white LEDs
Fuse values & types for: 120VAC operation: MDL or MDA 5 AMP / 250 Volt SLO-BLO size 1/4" X 1 1/4"
240VAC operation: MDL or MDA 3.15 AMP/ 250 Volt SLO-BLO size 1/4" X 1 1/4" B+ FUSE: MDA 1/2 AMP, 250 Volt SLO-BLO CERAMIC BODY size 1/4" X 1 1/4"
Dimensions: 15" deep x 13" wide x 8.75" tall
Shipping weight each: 45 pounds
Both amps combined its 100 Lbs for shipping
|
